1961 Volvo P1800 project, part 16

1961 Volvo Jensen P1800 paint and rust stripping

A lonely Volvo P1800 in a sea of Camaros, Mustangs and trucks. The body was dropped off in a “mall” of hot rod shops.

 

Hot rod shop

A quick peek in the hot rod shop revealed what is hot: MUSCLE CARS!! Pro Touring muscle cars is BIG. Let’s just say that Art Morrison is doing JUST fine!

OK, enough of that!

Since this is a unibody car I have elected to have the car dipped in order to remove all paint and rust. This treatment will remove all rust inside channels as well that you can’t get inside.

I have heard the anecdotal stories how the acid stays in seams and cause problems later. I discussed this in great length with the owner and he had not experienced any problems. This company has over 40 years experience with this. The last step of cleaning and neutralizing of the acid is the key.

65-Ford-Mustang-after-acid-dipping-2

Good eye there, skipper! That is not a Volvo. For informational purposes only, get it?

It is a rather elaborate process:

  • First it is submerged in a hot tank at 200 degrees
  • Then the car is cleaned with high pressure spray.
  • Bath that treats the rust and neutralize the paint removal chemicals.
  • High pressure rinse and clean.
  • Rust prevention coating.
  • Air dry.

Regardless, I plan to open up all critical seams, like rocker panels, front fenders, door skins, rear panel and rear quarter panel so all those seams will be exposed and I can clean all mating surfaces.

Once opened up, I can even touch up with sandblasting if needed. More on this later.

1961 Volvo Jensen P1800 hinge kit

“Hinge Kit” These are all the hinges and fastener needed to hang the hood, doors and the trunk. The body man will need this to line up all the panels etc.

 

1961 Volvo Jensen P1800 rear bumper parts car

This is why parts cars exists!  This 1964 coupe with chassis no 10764 is resting behind the shop and it is slowly returning to iron oxide but before that process is completed I am saving many parts for our project. I did not have the rear bumper bar, bumper bracket and the chrome piece in between the bumper sides. Now I do!

 

1961 Volvo Jensen P1800 rear bumper bracket

Of course I could not leave the chrome alone, I had to run some 0000 steel wool over the chrome. It still needs re-chroming but I feel better now! Don’t you?

 

1961 Volvo Jensen P1800 rear bumper bracket front 1

The bumper bracket looks like they will clean up good but it is what’s between them that worries me. Probably rust. They are conveniently rivited together!

 

1961 Volvo Jensen P1800 rear bumper bracket front

Yup, rust.They will spend a day or two in the vinegar bath.

 

1961 Volvo Jensen P1800 rear bumper bracket 2

The rear bumper brackets are riveted as well. Note the rivet head is flush on the rear bracket as they are flush with the channel they go in to. I have to make sure I duplicate this when it goes together.

 

1961 Volvo Jensen P1800 rear axle goop removal

Goop removing session number 543!!

 

1961 Volvo Jensen P1800 rear axle goop cutting

The goop on the rear axle is so thick that I can slice layers off…like a gyro !! Except it’s Swedish…Swyro! Glorious work!

 

1961 Volvo Jensen P1800 rear brake backing plate

It is pretty amazing how nice most of the chassis components are like this backing plate.It is still proudly displaying the factory semi gloss black. Not bad for a 56 year old car. It is still going to get blasted and powder coated.

 

1961 Volvo Jensen P1800 motor mount broken

Come on!! How can you brake a motor mount in a 90 hp Volvo. It was repaired by adding massive amount of brazing material. The parts car will once again step up and provide a replacement.

 

1961 Volvo Jensen P1800 idler arm

The early cars used a different idler arm and based on the profile on the arm, this is indeed the original part. I have chassis number 423 and the Volvo parts book tells me that the needle bearing still available are from chassic no 500 something and forward. Yet the specs on the bearings matches my early arm exactly so maybe I will be OK.

More later..

 

Volvo P1800 logga

 

1961 Volvo P1800 project, part 12

The body is finally stripped:

As mentioned in part 11, I discovered that the top bolt holding the vacuum tank was a Phillip head screw and obviously installed BEFORE the fenders were installed.

1961 Volvo Jensen P1800 brake tank screws

After a fair amount of “fiddling” we got the screw out. If you read up on Volvo 1800 history you will learn that the bodies were made by a company called Pressed Steel a few miles south of Glasgow. They were then sent on to Jensen for assembly.

Some smart ass at Pressed Steel grabbed a Phillip head screw for the top mounting of this tank as I am sure it was installed before the front fender was welded to the body.  Just to really mess with my head, they used hex bolts on the lower mounting point. Oh well!

 

1961 Volvo Jensen P1800 brake tank

This was an interesting surprice after I got the tank down. It felt very heavy. Guess what? It was full of break fluid. About two liters to be exact. I am going to guess that the brake booster failed at some point and the vacuum started to suck in the brake fluid. What is amazing is how much brake fluid the owner must have been adding to the brake cylinder.

I feel sorry for the poor owner that had to add fluid to that little master cylinder as the fluid was mysteriously disappearing! Maybe this was going on over many years, who knows.

The Jig is up!

1961 Volvo Jensen P1800 frame jig

I built a metal frame and I added support beams that will hold the body to the frame so it can be transported to paint stripping and body shop.

1961 Volvo Jensen P1800 empty body

I sacrificed my lawn tractor trailer for it’s wheels and also the beam that connects to the tractor. It is going to stripping in late April 2016.

Comparing equipment between the 1964 parts car and this 1961 car reveals some subtle differences.

1961 Volvo Jensen P1800 speedo

Like the tachometer for example. The red line on the 1961 is at 6000 rpm. The red line…ish starts at 5500. That is code for: Hey Sven, you better start thinking about popping this baby in to another gear or your push rods will start denting your hood!

By the way,  these gauges are just gorgeous!

 

1964 Volvo Jensen P1800 speedo

This one is not so gorgeous but it is from the 1964 parts car.  The red line starts at 6500 rpm. I guess Volvo got a little braver or they got better valve springs…or both.

 

1961 Volvo Jensen P1800 fuel gauge

Also, the fuel gauge is different. The indicator stems from the center unlike the ’64 model where it is off to the side. Not a big deal but I want to make sure I don’t mix them up.

 

1964 Volvo Jensen P1800 fuel gauge

1964 gauge. See how the needle stems from the side as opposed to the center.

 

1961 Volvo Jensen P1800 trim piece

Another note for the nuance department: The metal trim piece that is located inside the car on the top of the B-pillar was made of aluminum. (top) The later cars had this made in stainless.

 

1961 Volvo Jensen P1800 modular shop

Modular shop. Having the axles on the wheel dollies help when shop space is tight.

 

1961 Volvo Jensen P1800 key lock

I finally got the ignition lock cylinder back. I was very excited that they were able to make a key but the pretty chrome fascia was now sporting a big scratch. Idiots!

I will be looking for a new cylinder I guess. Got one? Early style with small cylinder diameter…please  Email me

Folks along the way:

One of the fun aspects of playing with old cars is the people you meet along the way.

Having the same interest is reason enough to spark a conversation between two strangers. Maybe they have that part you are looking for or vice verse or just comparing notes in general.

Dave Lucas in Columbus, Ohio checked in with me. He is knee deep in a restoration of a 1963 Volvo P1800. This is the before picture:

OLYMPUS DIGITAL CAMERA

Dave’s P1800 is chassis number 6065 so I am thinking it was assembled in Sweden. The transmission and engine has been rebuilt so now he is working on the body and interior. We look forward to updates.

 

Lucas 1963 Volvo P1800 dog

We know Dave is a good guy as he is also a dog person. Here his best friend is checking out the dismal back seat! “I think I will ride shotgun in the passenger seat”

 

Gary Ramstad 1967 Volvo 1800S

Gary Ramstad from Seattle is almost finished with his 1967 Volvo 1800S. He named it “Puzzle” as the assembly of all the interior pieces resembles a puzzle.

Mo later…

Volvo Wagon Meet in Sweden

Ragge Fransson was a relentless Volvo wagon and 123GT enthusiasts.

Story time…He was also a true gentleman: I had just connected with him about Volvos so he barely knew me. I was bidding from US on a rare Volvo part on a Swedish auction site. Turns out he was bidding as well. When he saw that I was the bidder he backed off and let me have the part. I did not know until later.

Unfortunately he left us last year…way too early. RIP Ragge!

Ragge sent us these pictures a few years ago from a wagon meet in Sweden.

OLYMPUS DIGITAL CAMERA

Vintage Volvo meet in Sweden 122 wagon red

The red wagon is a 1968, Automatic.

Vintage Volvo meet in Sweden 122 wagon red side

Vintage Volvo meet in Sweden 122 wagon red interior

Vintage Volvo meet in Sweden 122 wagon white

Vintage Volvo meet in Sweden 122 wagon blue

Roof rack is the norm.

Vintage Volvo meet in Sweden 122 wagons more

 

Vintage Volvo meet in Sweden Ragge

Ragge Franssons 1968 122 Wagon Sport.

Vintage Volvo meet in Sweden Ragge rear

They look great with the 5.5 inch wide rims. Tires are 195-60-15

Vintage Volvo meet in Sweden 122 wagons

Photo: Ragge Fransson

Bonus picture:

Volvo PV544

Magnus Johansson from Karlshamn, Sweden sent us this picture of his car and trailer.  The car is a 1965 Volvo PV 544 Sport. The car is un-restored and is even sporting the original paint. The trailer is an Opio also from 1965.

Welcome to Vintage Swedish Cars

(do you think our logo is big enough??

1967 Volvo Combi

Here we will babble randomly about those fine Swedish cars made from the original Volvo Jacob to cool 240’s and 700 series cars.  The emphasis will be on cars from the 60’s as we find the Volvo 120 series Amazons and the Volvo PV 444-544 cars the ultimate in Swedish Coolness.

Stand by for Swedish stuff.

VSC Logo600X114